Aemic Corporation is a manufacturer of Electrical & Test Equipment that specializes in capacitor checker and resistor checker. » Capacitance checker

AE-3245A 5 Rank sortiing C-tanδChecker

admin_satoru — Sun, 25 Oct 2015 00:17:15 +0000

Optimum Check in an aging process of electrolytic capacitor

Contact-check is equipped as standard function.
Measuring frequency: 120Hz
Measuring time: approx.105msc.[Including contact check & residual voltage check]
Measuring range: 0～39.99mF]/tanδ0～199.9%]
5 Rank sorting.
Centronics interface as standard.

Measuring range and Accuracy（Ambient temperature 23℃±5℃）

Range	400nF	4μF	40μF	400μF	4mF	40mF
C Accuracy	within ±0.5%±2(digits)				within±2%±2(digits)	within ±2%±5(digits)
tanδ Accuracy
Test Mode	Serial or Parallel equivalent circuit

In case of tanδ value is 100.0%～199.9%, Accuracy of C and tanδ becomes double.

Measuring Mode：	Serial Equivalent Circuit
Measuring Voltage：	Below 400mV (r.m.s.)
Measuring Method：	5 Terminal Measurement
Measuring Frequency：	120Hz±0.1%、sine wave
Measuring Terminal：/th>	Front panel: 5-terminal Rear panel: 8 Pins round type metal consent
Contact Check：	Function to output the measurement error when the contact resistance over about 200Ωis detected at the input terminals more than one.
Input Protection：	Function to protect the measurement circuit when the voltage on the measurement sample which has not been discharged is detected being more than about DC2.2V at the continual 4 terminals. (Residual voltage check)
Measurement Time：	Remote start Mode: Appr. 105msec. 【Contact check & Residual voltage check】: Appr. 27msec. 【Measurement stabilization time】 : Appr. 45msec. 【Time until the measurement terminal release】Appr. 96msec. Free running Mode: Appr. 3 cycles/sec.
Comparator setting：	Capacity C ： 4 points of LL, L, H and HH : “200 to 3999” Loss tanδ : “1 to 199.9”
Comparator Judgment :	Digital data comparison method
Judgment Result Display：	Capacity: CLO, CLG, CGO, CHG, CHI Tanδ : DGO, DNG Total : C/D-GO
Control Signal：	Input: START, HOLD, RESET, CINH, SHIFT, NINH, GINH Output: GO1. GO2, CNG, DNG, CER, COV, DER, DOV, CEND, MEDD, BUSY, SLCT, CCE, VCE and various type of shift judgment.
Data Interface：	Centronics
Use environment：	Temp.：0℃～+40℃、 Humidity：below 80% or less (no condensation)
Power supply：	AC85V～265V、50～60Hz、appr. 45VA
Outer dimension：	432(W)×149(H)×450(D)mm（excluding protruding parts such as rubber legs, etc.）
Weight：	Appr. 10kg

※ We will change the specifications of the catalogue without notice by improvement.

AE-363D Ultra High Speed and High Accuracy, 1kHz Digital Capacitor Checker

admin_masahiro — Thu, 03 Apr 2014 08:16:53 +0000

Optimum for the use on a taping machine for chip and MELF type capacitor.

Ultra-high speed : 1msec【TYP】
Range of measurement : 20pF～200µF
Measuring frequency : 1kHz±0.1%(Sine wave)
RS-232C and Centronics interface are built-in as standard equipment.【GP-IB is option】

Measuring range and Accuracy : D＜0.5 (at 23℃±5℃)

Range	Accuracy	Measuring voltage
20pF	within ±0.2% of rdg±3digit	about 1V
200pF	within ±0.2% of rdg±2digit
2nF
20nF
200nF
2μF
20μF		below 1V
200μF	within ±0.5% of rdg±3digit[100μF≧] within(±0.5% of rdg±3digit)×Measuring value/100[100μF＜]	below 1V

Measuring method :	5-terminal measurement, parallel equivalent circuit
Measuring frequency :	1kHz±0.1%、Sine wave
Stray capacity cancel range :	about 20pF
Full scale and zero temp. coefficient :	within ±100ppm/℃
Comparator setting range :	【Remote start】1.9msec.～11.5msec.
Comparator setting range :	【Free running】5～14times/sec.
Operation condition :	【Temp.】0℃～+50℃、【Humidity】below 85%
Power supply :	AC85V～265V、50～60Hz、about 60VA
Outer dimension :	333(W)×99(H)×300(D)mm【excluding protruding parts such as rubber legs, etc.】
Weight :	about 4kg
Option :	GP-IB Interface

AE-365E Ultra high speed & high accuracy 120Hz/1kHz Digital Capacitor Checker

admin_masahiro — Mon, 03 Mar 2014 08:18:08 +0000

Optimum model for inspection on taping machine of “CHIP”, “MELF”, “RADIAL” and “AXIAL” Capacitor.

Ultra-high speed : 1msec【TYP】
Range of measurement : 20pF～200µF
Contact checking function as standard
RS-232C and Centronics interface are built-in as standard equipment.【GP-IB is option】
Measuring frequency : 1kHz±0.1%(Sine wave)

Measurning range and Accuracy（D＜0.1 Ambient temperature 23℃±5℃）

Range	Measuring range	Resolution	Accuracy	Measurement voltage
2pF	0.000pF～1.999pF	0.001pF	Within ±1.0% of rdg±5digit×α	1kHz,1V±5％ [rms]	1kHz,5V±5V％ [rms]
20pF	0.00pF～19.99pF	0.01pF	Within ±0.25% of rdg±3digit×α		1kHz,5V±5V％ [rms]
200pF	0.0pF～199.9pF	0.1pF	Within ±0.2% of rdg±2digit×α		—-
2nF	0.000nF～1.999nF	0.001nF	Within ±0.2% of rdg±2digit		—-
20nF	0.00nF～19.99nF	0.01nF			—-
200nF	0.0nF～199.9nF	0.1nF			—-
2μF	0.000μF～1.999μF	0.001μF			120Hz、0.5V±5％ [rms]
20μF	0.00μF～19.99μF	0.01μF	Within ±0.3% of rdg±3digit×α		120Hz、0.5V±5％ [rms]
120μF	0.0μF～119.9μF	0.1μF	Within ±1.0% of rdg±5digit×α	1kHz,1V+5％～-15％ [rms]	—-
200μF	0.0μF～199.9μF	0.1μF	Within ±0.5% of rdg±3digit×α	—-	120Hz、0.5V±5％ [rms]
1.2mF	0.000mF～1.199mF	0.001mF	Within ±1.5% of rdg±5digit×α	—-	120Hz、0.5V+5％～5％～-25％ [rms]

※In case of 0.1＜D＜1, 25D/100(%)is added on the above accuracy.　
α：In cae of FAST 2(In case of 2pF Range/1 V α=10) In case of SLOW 1(In case of 2pF Range/1 V α=5)

Measurement Method	3/5 terminal measurement [Available to select the measuring method on each range]
Measuring Frequency	120Hz/1kHz±0.1%、sine wave
Output Impedance	Approx. 1Ω
Straycapacity revision range	Approx. 30pF
temperature coefficient	Within ±100ppm/℃[f.s and zero]
Measurement time	【Free running】FAST：Aprrox.1～5 time/sec. SLOW：FAST×N(N: The setting number of “average” )
Measurement time	【Start trigger signal [FAST]】1msec.[Fastest time]
Comparator set range	Capacitance：1999[120µF/1.2mF range: 1199] with HI and LO limit tanδ：99.9%
Use environment	Temperature：0℃～+50℃、　Humidity：Less than 85%
Power supply	AC85V～265V、50～60Hz、Aprrox. 50VA
Outer dimension	333(W)×99(H)×300(D)mm
Weight	Approx. 4kg

AE-3122A High Speed Type・120Hz Digital Capacitor Checker

admin_masahiro — Fri, 07 Feb 2014 03:35:17 +0000

Optimum for the use on a taping machine for Aluminum Electrolytic Capacitor and Tantalum Capacitor.

Measuring range：100nF～9.99mF/-79.9%～+99.9%
４-Terminal measurement.
High speed integration method measurement.
Measuring value is displayed in percentage against the reference capacitance value set
Digitally and comparison result by built-in comparator is displayed as –NG,GO,+NG by LED and buzzer.
BCD parallel out available.
External DC bias possible(max.DC25V)

Range No.	Measuring range	Test voltage	Accuracy
1	100nF～999nF	within 100mV(r.m.s)	within±0.25%±1digit
2	1μF～9.99μF
3	10μF～99.9μF
4	100μF～999μF
5	1mF～9.99mF		within±0.5%±3digit

Measuring method:	4-terminal measuring method、serial equivalent circuit.
Measuring frequency:	120Hz±0.1%, sine wave form.
Measuring time:	【in case of remote start mode】about 25msec.
Measuring time:	【in case of free running mode】about 37.5time/sec.
Display of measured value:	-79.9％～+99.9％
Comparator setting range:	Upper limit：0.0%～+99.9%,　Lower limit：0.0%～-79.9%
Input and output signal:	Remote start input：0～+12V or open collector.
	Comparison result output[LO/GO/HI]：open collector [max.80V/100mA]
	End of measurement output[EOC]：open collector [max.80V/100mA]
	BCD parallel output of measuring value：TTL fan out 2
Operating condition:	Temp.：0℃～+50℃、　Humidity：below 85%
Power supply:	AC85V～265V、50～60Hz、about 20VA
Outer dimension:	250(W)×89(H)×250(D)mm（excluding protruding parts such as rubber legs, etc.）
Weight:	2kg approx.

※　We will change the specifications of the catalogue without notice by improvement.

AE-369B 120Hz/1kHz High Speed Digital C-tanδ Checker

admin_masahiro — Fri, 07 Feb 2014 03:30:53 +0000

Optimum for the sorting machine of Aluminum and Tantalum Electrolytic Capacitor.

Measuring frequency 120Hz/1kHz[Sine wave]
Measuring speed 8.2msec.(1kHz)/12.5msec.(120Hz)
Measuring range 　 C：0～39.99mF/tanδ：0～199.9%
Test mode Serial or Parallel equivalent circuit.
Comparison output by the built-in comparator.
Data interface Either GP-IB、RS-232C or Centronics.【Option】

Measuring range and Accuracy（Ambient temperature 23℃±5℃）

Range	1kHz	40nF	400nF	4μF	40μF	400μF	4mF
Range	120Hz	400nF	4μF	40μF	400μF	4mF	40mF
C Accuracy	±0.3％±2(digit)					±y％±2(digit)	±1％±5(digit)
tanδ Accuracy
Test Mode	Serial or Parallel equivalent circuit

β：5(120Hz) / 10(1kHz)
γ：1(120Hz) / 0.5(1kHz)
In case of tanδ value is 100.0%～199.9%, Accuracy of C and tanδ becomes double.

Measuring Method	5 Terminal Measurement
Measurement Voltage	Below 400mV (r.m.s.)
Measuring Frequency	120Hz/1kHz±0.1%、sine wave
Measurement Time	【Remote start】about 8.2msec.(1kHz) / about 12.5msec.(120Hz)
Measurement Time	【Free running】about 3 time/sec.
DCDC Bias	DC1.5V（built-in）and DC 0～25V(remote)
Use environment	Temp.：0℃～+50℃、　Humidity：below 80%
Power supply	AC85V～265V、50～60Hz、about 30VA
Outer dimension	333(W)×99(H)×300(D)mm（excluding protruding parts such as rubber legs, etc.）
Weight	Approx. 3.8kg

RS-232C
GP-IB	Only one kind of interface can be provided with the checker
Centronics Interface

※　We will change the specifications of the catalogue without notice by improvement.

AE-323A High Speed Type・1kHz Digital Capacitor Checker

admin_masahiro — Tue, 07 Jan 2014 03:35:40 +0000

Optimum for the use on a taping machine for Film Capacitor and Ceramic Capacitor.

Measuring range：10pF～9.99μF/±99.9%
5-Terminal measurement.
High speed integration method measurement.
Measuring value is displayed in percentage against the reference capacitance value set
Digitally and comparison result by built-in comparator is displayed as –NG,GO,+NG by LED and buzzer.
BCD parallel out available.
External DC bias possible(max.DC25V)

Range No.	Measuring range	Test voltage	Accuracy
0	10pF～99.9pF	1V(r.m.s)approx.	within±0.25%±0.25p±1digit
1	100pF～999pF
2	1nF～9.99nF
3	10nF～99.9nF
4	100nF～999nF
5	1μF～9.99μF

Measuring method:	5-terminal measuring method、parallel equivalent circuit.
Measuring frequency:	1kHz±0.1%, sine wave form.
Stray capacitance cancel range:	10pF approx.
Measuring time:	【in case of remote start mode】about 3.2msec.
Measuring time:	【in case of free running mode】about 68time/sec.
Comparator setting range:	Upper limit：0.0%～+99.9%,　Lower limit：0.0%～-99.9%
Display of comparison result by comparator:	LED display of -NG/GO/+NG, and buzzer.
Comparator setting range:	Upper limit : 0.0% ～ +99.9%, Lower limit : 0.0% ～ -99.9%
Display of comparison result by comparator:	LED display of -NG/GO/+NG,and buzzer.
Input and output signal:	Remote start input：0～+12V or open collector.
	Remote start input：0～+12V or open collector.
	End of measurement output[EOC]：open collector [max.80V/100mA]
	BCD parallel output of measuring value：TTL fan out 2
Operating condition:	Temp.：0℃～+50℃、　Humidity：below 85%
Power supply:	AC85V～265V、50～60Hz、about 15VA
Outer dimension:	250(W)×89(H)×250(D)mm（excluding protruding parts such as rubber legs, etc.）
Weight:	2kg approx.

※　We will change the specifications of the catalogue without notice by improvement.